******************************************************************************************************************************
Connecting to first device: success
******************************************************************************************************************************
	******************************************
	OpenOCD console output for first device
	******************************************

		Open On-Chip Debugger 0.10.0-dev-00007-g58350bc-dirty (2018-01-12-12:21)
		Licensed under GNU GPL v2
		For bug reports, read
			http://openocd.org/doc/doxygen/bugs.html
		srst_only separate srst_nogate srst_open_drain connect_assert_srst
		Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
		adapter_nsrst_delay: 100
		adapter speed: 1800 kHz
		Info : tcl server disabled
		Info : telnet server disabled
		Info : clock speed 1800 kHz
		Info : STLINK v2 JTAG v31 API v2 SWIM v7 VID 0x0483 PID 0x3748
		Info : vid/pid are not identical: 0x0483/0x374B 0x0483/0x3748
		Info : using stlink api v2
		Info : Target voltage: 3.216820
		Info : Stlink adapter speed set to 1800 kHz
		Info : STM32F407VGTx.cpu: hardware has 6 breakpoints, 4 watchpoints
		Info : accepting 'gdb' connection on tcp/3333
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : device id = 0x10076413
		Info : flash size = 1024kbytes
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0xfffffffe msp: 0xfffffffc
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Padding image section 0 with 261752 bytes
		target halted due to breakpoint, current mode: Thread 
		xPSR: 0x61000000 pc: 0x20000046 msp: 0xfffffffc
		Warn : keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (4772). Workaround: increase "set remotetimeout" in GDB
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000

******************************************************************************************************************************
Connecting to second device: success
******************************************************************************************************************************
	******************************************
	OpenOCD console output for second device
	******************************************

		Open On-Chip Debugger 0.10.0-dev-00007-g58350bc-dirty (2018-01-12-12:21)
		Licensed under GNU GPL v2
		For bug reports, read
			http://openocd.org/doc/doxygen/bugs.html
		srst_only separate srst_nogate srst_open_drain connect_assert_srst
		Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
		adapter_nsrst_delay: 100
		adapter speed: 1800 kHz
		Info : tcl server disabled
		Info : telnet server disabled
		Info : clock speed 1800 kHz
		Error: libusb_open() failed with LIBUSB_ERROR_ACCESS
		Info : STLINK v2 JTAG v31 API v2 SWIM v7 VID 0x0483 PID 0x3748
		Info : vid/pid are not identical: 0x0483/0x374B 0x0483/0x3748
		Info : using stlink api v2
		Info : Target voltage: 3.216820
		Info : Stlink adapter speed set to 1800 kHz
		Info : STM32F407VGTx.cpu: hardware has 6 breakpoints, 4 watchpoints
		Info : accepting 'gdb' connection on tcp/4444
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08009bac msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : device id = 0x10076413
		Info : flash size = 1024kbytes
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08009bac msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0xfffffffe msp: 0xfffffffc
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Padding image section 0 with 261752 bytes
		target halted due to breakpoint, current mode: Thread 
		xPSR: 0x61000000 pc: 0x20000046 msp: 0xfffffffc
		Warn : keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (3858). Workaround: increase "set remotetimeout" in GDB
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
	

	******************************************
	OpenOCD console output for first device
	******************************************

		Open On-Chip Debugger 0.10.0-dev-00007-g58350bc-dirty (2018-01-12-12:21)
		Licensed under GNU GPL v2
		For bug reports, read
			http://openocd.org/doc/doxygen/bugs.html
		srst_only separate srst_nogate srst_open_drain connect_assert_srst
		Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
		adapter_nsrst_delay: 100
		adapter speed: 1800 kHz
		Info : tcl server disabled
		Info : telnet server disabled
		Info : clock speed 1800 kHz
		Info : STLINK v2 JTAG v31 API v2 SWIM v7 VID 0x0483 PID 0x3748
		Info : vid/pid are not identical: 0x0483/0x374B 0x0483/0x3748
		Info : using stlink api v2
		Info : Target voltage: 3.216820
		Info : Stlink adapter speed set to 1800 kHz
		Info : STM32F407VGTx.cpu: hardware has 6 breakpoints, 4 watchpoints
		Info : accepting 'gdb' connection on tcp/3333
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : device id = 0x10076413
		Info : flash size = 1024kbytes
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0xfffffffe msp: 0xfffffffc
		configuring PLL
		Info : Stlink adapter speed set to 4000 kHz
		adapter speed: 4000 kHz
		Info : Padding image section 0 with 261752 bytes
		target halted due to breakpoint, current mode: Thread 
		xPSR: 0x61000000 pc: 0x20000046 msp: 0xfffffffc
		Warn : keep_alive() was not invoked in the 1000ms timelimit. GDB alive packet not sent! (4772). Workaround: increase "set remotetimeout" in GDB
		Info : Stlink adapter speed set to 1800 kHz
		adapter speed: 1800 kHz
		target halted due to debug-request, current mode: Thread 
		xPSR: 0x01000000 pc: 0x08042734 msp: 0x20020000
